MLCC Application Note: GRM187R61A226ME15J Best Practices
The Murata GRM187R61A226ME15J is a 22µF, 10V, X5R dielectric, 0603-size multilayer ceramic capacitor (MLCC) designed for general-purpose decoupling and filtering in power distribution networks. This application note provides practical guidance for integrating this component into your designs, focusing on circuit topologies, board layout, and testing to ensure robust performance.
Recommended circuit topologies and design best practices for the GRM187R61A226ME15J center on its role as a bulk decoupling capacitor. In a typical low-dropout regulator (LDO) or DC/DC converter output stage, place this MLCC as close as possible to the load’s power input pins. For a processor or FPGA core supply, use one GRM187R61A226ME15J per power pin, supplemented by smaller 100nF and 1nF capacitors to cover high-frequency noise. In multi-rail systems, avoid sharing a single MLCC between different voltage domains to prevent cross-coupling. For input-side decoupling of a switching regulator, place a 10µF to 22µF MLCC directly at the input pin, but ensure the total capacitance does not exceed the regulator’s maximum input capacitance specification to avoid inrush current issues. When using this capacitor in series with a resistor for an RC snubber circuit (e.g., across a MOSFET drain-source), calculate the resistor value to dampen ringing without exceeding the capacitor’s rated ripple current—typically 0.5A to 1A for this size. Always derate the capacitance by 30-50% for X5R dielectrics at applied DC bias near 10V, so for a 22µF part, expect effective capacitance of approximately 10-12µF at 5V DC. Verify your nominal voltage is at least 20% below the rated 10V.
Component selection guidelines for supporting passives ensure optimal performance with the GRM187R61A226ME15J. When pairing with inductors in a buck converter output filter, choose an inductor with a saturation current rating at least 1.5 times the peak load current to prevent core saturation, which can cause current spikes that stress the MLCC. For input filters, use a ferrite bead with impedance >100Ω at 100MHz in series with the MLCC to suppress conducted EMI. The series resistor for an RC snubber should be a 0603 or 0805 thick-film type with a power rating of at least 0.1W, and its resistance value should be between 0.5Ω and 5Ω to avoid excessive power dissipation. For bypassing high-speed digital ICs (e.g., DDR memory), combine the GRM187R61A226ME15J with a 0.1µF X7R capacitor and a 10nF C0G capacitor to create a low-impedance path from 1MHz to 1GHz. Always use capacitors with similar or better temperature stability (X5R or X7R) for adjacent decoupling to avoid resonance shifts. Avoid using Y5V dielectrics near the GRM187R61A226ME15J because their high voltage coefficient can cause unpredictable system behavior.
PCB layout recommendations and routing tips are critical for maximizing the GRM187R61A226ME15J’s decoupling effectiveness. Place the capacitor within 2mm of the IC’s power and ground pins, with the trace width equal to the pad size (typically 0.9mm for 0603). Use a direct via-in-pad (VIP) connection to the power plane for the capacitor’s anode pad, and a second via to the ground plane for the cathode pad. If via-in-pad is not possible, use a 0.3mm via placed 0.5mm from each pad, connected by short, 0.3mm-wide traces. For multi-layer boards, place the MLCC on the same layer as the IC to avoid additional inductance from vias. In high-current paths (e.g., >1A), use a copper pour under the capacitor that connects to the power plane through multiple vias to reduce resistive drops. For differential pairs or high-speed signals, keep the MLCC’s return current path as short as possible—avoid routing the capacitor’s ground pad through a long trace to a distant ground via. Instead, place a ground via directly adjacent to the ground pad. For RF circuits, ensure the capacitor’s orientation (longer dimension parallel to current flow) to minimize parasitic inductance. Use a solder mask dam between the capacitor pads to prevent solder bridging, especially when using low-profile 0603 parts.
EMC/EMI considerations and mitigation strategies involve the GRM187R61A226ME15J’s self-resonant frequency (SRF), which is typically around 3-5 MHz for a 22µF MLCC in 0603 size. At frequencies above SRF, the capacitor becomes inductive, so for suppressing high-frequency noise (e.g., >10 MHz), add a 100nF MLCC in parallel. To minimize radiated emissions from switching converters, place the input and output MLCCs as close to the converter IC as possible, forming a low-inductance loop. Use a ground plane directly under the capacitor and converter to act as a shield. For conducted emissions, insert a 1-10Ω resistor in series with the MLCC to dampen ringing at the switching node, but ensure the resistor’s power rating is adequate—use a 0603 0.1W resistor for currents up to 100mA. Avoid long traces connecting the MLCC to the IC, as they act as antennas; keep trace lengths under 5mm. In multi-layer boards, place a separate ground plane layer adjacent to the power plane to create a low-impedance return path. For systems with high dV/dt (e.g., >10V/ns), use the GRM187R61A226ME15J in combination with a 1nF C0G capacitor to handle fast transients, as the MLCC’s dielectric absorption can cause voltage spikes. Always verify EMI performance in a pre-compliance chamber after prototype assembly.
Common design pitfalls and how to avoid them include underestimating DC bias effects: the GRM187R61A226ME15J’s capacitance drops by up to 60% at 10V DC. Always measure effective capacitance at your operating voltage using an LCR meter with DC bias, and if necessary, use a higher voltage rating (e.g., 16V) to maintain capacitance. Another pitfall is ignoring AC ripple current—this MLCC has a ripple current rating of approximately 0.7A RMS at 100kHz. Exceeding this can cause self-heating and reduced lifespan. Calculate ripple current using I = C * dV/dt, and if it exceeds the rating, use two capacitors in parallel. A third pitfall is incorrect orientation: the GRM187R61A226ME15J is non-polarized, but its internal structure has a slight asymmetry. For high-frequency applications, orient the capacitor so that its internal electrodes run parallel to the current flow to minimize ESL. Avoid using this MLCC in series with high-ESR components (e.g., large electrolytics) without considering the resulting RC time constant, which can cause slow transient response. Finally, do not place the MLCC near heat sources (e.g., hot components or vias) because X5R dielectric loses capacitance at elevated temperatures—keep ambient temperature below 85°C.
Prototyping tips and bench testing procedures for the GRM187R61A226ME15J ensure design validation. Start with a functional prototype using a 2-layer PCB with ground plane. Solder the MLCC using leaded solder (Sn63Pb37) at 230°C for 3 seconds maximum to avoid thermal shock—use a hot air rework station with a 1mm nozzle. After assembly, verify capacitance with an LCR meter at 1kHz and 1V AC bias, then apply your DC operating voltage and measure the effective capacitance again using a DC bias fixture (e.g., Keysight 16334A). For transient testing, connect a 1A electronic load with a 1A/µs slew rate to the output and capture voltage ripple on a 500MHz oscilloscope with a 10x probe (use a ground spring to minimize loop inductance). Expected ripple should be <50mV for a 22µF MLCC. For high-frequency noise, use a near-field probe (e.g., Langer RF-R 400-1) to scan the board around the MLCC between 30MHz and 1GHz. If noise exceeds 40dBµV, add a 100nF MLCC in parallel. For thermal testing, run the circuit at full load for 30 minutes and measure the MLCC’s case temperature with a thermocouple—it should not exceed 85°C. Document all results and compare with simulation models from Murata’s SimSurfing tool to refine your design before production.

