Home / Industry News

AWNING ECH23-3N Datasheet Guide: Dimensions & Specs Explained

GQGF LIMITED · 2026-07-20

Interpreting a datasheet for a component like the AWNING 3-3/8'WX2'HX3'D (Brand: Awntech, SKU: ECH23-3N) requires a shift in perspective from standard semiconductor or passive component analysis. This is not an electronic component in the traditional sense but rather a mechanical assembly—a retractable awning system—where the electrical specifications govern the motor and control unit, while the mechanical dimensions define the physical envelope and installation constraints. The given SKU suggests a 3-foot width, 2-foot projection, and 3-foot height for the fabric drop, but the critical electrical data will reside in the motor’s datasheet, which is often integrated into the awning assembly. For this guide, we will interpret the component as a complete system, focusing on the motor drive, power requirements, and control interfaces typically found in such products.

Key electrical specifications and what they mean in practice for the ECH23-3N are likely centered on the tubular motor’s voltage, current, and power ratings. A typical awning motor operates at 120VAC or 24VDC, with a nominal current draw ranging from 1 to 3 amps under load. The power rating, often expressed in horsepower (HP) or watts (W), dictates the maximum torque the motor can apply to extend or retract the fabric. In practice, a 1/15 HP motor would be sufficient for a small 3-foot awning, but the exact value must be verified from the motor’s label. The duty cycle rating—usually expressed as a percentage like 10% or 20%—tells you the maximum on-time relative to a full cycle (e.g., 2 minutes of operation followed by 18 minutes of rest). This is critical: exceeding the duty cycle can cause thermal overload and premature motor failure, especially in applications requiring frequent adjustments. The motor’s rotational speed, given in revolutions per minute (RPM), correlates to extension/retraction speed; a typical range is 15-30 RPM, translating to a fabric travel time of 10-20 seconds for a 3-foot width. For the control circuit, you may see limit switch ratings (e.g., 10A at 125VAC) and wireless receiver sensitivity (e.g., -100 dBm for 433 MHz RF remotes), which impact reliability in noisy environments.

Absolute maximum ratings and derating considerations are paramount for long-term reliability. The motor’s absolute maximum voltage might be 130VAC for a 120VAC unit, but sustained operation at this level increases winding temperature and reduces insulation life. Similarly, the maximum current draw is typically 20-30% above the nominal rating, but you should never design for continuous operation at this limit. Derating is applied by reducing the applied voltage or load torque. For example, if the motor is rated for 1.5A at 120VAC, a safe operating point might be 1.2A at 110VAC, which lowers copper losses and extends lifespan. The ambient temperature rating is often 0-40°C for standard motors; derating the current by 10% for every 10°C above 40°C is prudent. For the control electronics, the absolute maximum input voltage for the receiver might be 15VDC on a 12VDC rail; a derating to 12.5VDC ensures the regulator stays within safe margins. The mechanical limits are also absolute: the 3-3/8' width (approx. 40.5 inches) and 2-foot projection must not be exceeded, as the fabric and frame are designed for these specific dimensions. Overextending the fabric can cause stress on the roller tube and brackets, leading to binding or catastrophic failure.

Typical application circuit analysis for the ECH23-3N involves a straightforward AC or DC motor drive with limit switches and a control interface. For a 120VAC unit, the circuit includes a capacitor-start motor (often with a 5-10 µF run capacitor), a thermal overload protector (typically a bimetallic switch that opens at 105°C), and two limit switches (one for extension, one for retraction) that are mechanically actuated by the roller tube’s rotation. The control circuit may feature a wireless receiver module (e.g., 433 MHz) that drives a relay or triac to switch the motor. A typical schematic would show the line and neutral terminals, with the motor’s forward and reverse windings connected through a DPDT relay. The limit switches are wired in series with the respective direction coils to stop motion at the endpoints. For a 24VDC system, the circuit uses an H-bridge driver (like an L298N or integrated motor controller) with PWM input for speed control, but this is less common in basic awnings. Key analysis points include verifying that the relay contacts are rated for the motor’s inrush current (which can be 3-5x the running current) and that the thermal protector is properly sized to prevent damage during a stalled condition.

Pin configuration and package considerations for this awning component are not standard IC pinouts but rather terminal connections and mechanical mounting points. The motor typically has three or four wires: common (neutral), forward (extend), reverse (retract), and sometimes a ground or capacitor lead. On the control box, you will find screw terminals labeled L, N, COM, EXT, RET, and possibly a GND for the radio receiver. The package is the entire awning assembly—a 3-foot wide, 2-foot deep, 3-foot high structure—which requires a sturdy mounting surface like a brick wall or wooden fascia. The roller tube diameter (often 3.5 to 4 inches) and the bracket spacing must align with the 3-3/8' width. The fabric drop of 3 feet (36 inches) dictates the clearance needed below the awning. Installation considerations include ensuring the brackets are anchored into structural supports (e.g., studs or masonry anchors) and that the awning’s slope angle (typically 15-30 degrees) allows proper water runoff. The control box should be mounted in a weather-resistant location, away from direct rain, with cable glands for strain relief.

Thermal management guidelines focus on the motor and controller. The motor’s housing is often aluminum to dissipate heat, but it relies on natural convection. For the ECH23-3N, ensure there is at least 2 inches of clearance around the motor for airflow. If the awning is installed in a hot attic or south-facing wall, consider adding a small fan or relocating the controller to a cooler space. The motor’s thermal protector will cut power if internal temperatures exceed 105°C, but repeated tripping indicates poor design. For the control electronics, the relay or triac generates heat proportional to the current squared; a heatsink rated for 10-15°C/W is typical. In 24VDC systems, the H-bridge IC may require a heatsink if the motor draws more than 2A continuously. Derating the ambient temperature by 10-20% from the maximum rating (often 50°C) is recommended for reliability in outdoor installations.

How to read and interpret the timing diagrams or characteristic curves for this component is less about oscilloscope plots and more about mechanical travel profiles. A typical timing diagram for the motor’s extension cycle would show the current spike during startup (lasting 100-200 ms) followed by a steady-state current until the limit switch is reached. The retraction diagram is similar but with reverse polarity. The characteristic curves you might find include torque vs. speed (a linear decrease from stall torque to no-load speed) and current vs. load. For a 2-foot projection, the fabric weight is minimal, so the motor operates near no-load conditions. The torque curve helps you determine if the motor can handle wind loads—a gust of 20 mph can increase the load on the fabric, requiring a safety margin. The duty cycle diagram is a simple on/off timing plot showing the permissible on-time (e.g., 2 minutes) and off-time (18 minutes) to avoid overheating. When reading these, always note the conditions (e.g., at 120VAC, 25°C ambient) and apply derating if your environment differs. A key insight: if the extension time increases noticeably from the datasheet value (e.g., from 12 seconds to 18 seconds), it indicates increased friction or a failing motor, prompting maintenance.

ECH23-3N

AWNING 3-3/8'WX2'HX3'D

Awntech | ECH23-3N | $509.82

View Product →

Related Products

Part Number / DescriptionManufacturer PackageUnit PriceAvailability QTYAdd To Cart
AWNING 3-3/8'WX2'HX3'D AWNING 3-3/8'WX2'HX3'D Awntech— $509.82 Out of Stock0 pcs
Nginx server needs to configure pseudo-static rules, click View configuration method