Home / News

LED Floodlight Mini 50W Design: Compact 5400LM Build Guide

GQGF LIMITED · 2026-08-01

Introduction to the Component
The Interlight LED Floodlight Mini 50W-5400LM (SKU: WX-DTVY-2) is an ideal teaching platform for power electronics and thermal management. Unlike bare LEDs, this integrated unit contains a constant-current driver, an aluminum PCB, and a high-efficiency optic. Its 5400-lumen output at 50W means a luminous efficacy of 108 lm/W, which is typical of modern mid-power LEDs. For this tutorial, we will design a universal AC-input (100–240VAC) dimmable driver circuit that replaces the internal constant-current source, giving you hands-on experience with offline flyback converters, PFC (power factor correction), and analog dimming. The floodlight’s existing thermal path (die-cast housing) makes it safe to push to full rated current, but we will also design a thermal shutdown protection.

Design Requirements and Specifications
Target specifications for our driver:
- Input: 100–240VAC, 50/60Hz, power factor >0.9 (for compliance with EN 61000-3-2)
- Output: Constant current 1.4A (±3%) at a forward voltage range of 28–36V (typical for a 50W COB LED)
- Dimming: 0–10V analog input, 10%–100% output current
- Efficiency: ≥90% at 230VAC
- Protection: Over-temperature (LED case >85°C), over-voltage (38V), and short-circuit
We will use a flyback topology in critical conduction mode (CrCM) with a dedicated PFC controller (e.g., L6562A) to achieve both high PF and simple control. The LED string’s forward voltage varies with temperature, so we need a current-sense resistor with low drift.

Step-by-Step Design Process with Calculations
Step 1: Define output power. P_out = 50W nominal. Assume 90% efficiency, so P_in = 55.6W. At 100VAC min, peak input current I_pk = (P_in √2) / V_rms_min = (55.6 1.414) / 100 = 0.786A.
Step 2: Flyback transformer design. For CrCM, choose a switching frequency f_sw = 65kHz. The primary inductance L_p = (V_in_min_dc D_max)² / (2 P_in f_sw). With V_in_min_dc = 120V (after rectification), D_max = 0.45, L_p = (1200.45)² / (255.665,000) = 2916 / 7.23M ≈ 403µH. We will use a PQ2620 ferrite core with a 0.25mm air gap.
Step 3: Turns ratio. N_p/N_s = (V_in_min_dc D_max) / [(V_out + V_diode) (1-D_max)] = (1200.45) / [(36+0.7)0.55] = 54 / 20.2 ≈ 2.67. Choose N_p=32 turns, N_s=12 turns, auxiliary N_a=6 turns.
Step 4: Current sense resistor. For 1.4A output, reflected to primary, the peak current I_ppk = (2 P_out) / (V_in_min_dc D_max) = 100 / 54 = 1.85A. Use a 0.1Ω resistor, sensing voltage = 0.185V – within the L6562A’s 1V limit. For dimming, we will use a PWM-to-analog converter to adjust the reference voltage on the current-sense comparator.

Component Selection Rationale for the Complete BOM
- Controller IC: ST L6562A – runs CrCM with built-in PFC, low start-up current (50µA), and brown-out protection.
- MOSFET: 650V, 8A, R_DS(on)=0.65Ω – IPD65R950CFD from Infineon, chosen for low switching losses at 65kHz.
- Output diode: STTH12R06 (600V, 12A) – fast recovery, low forward drop (1.5V) to minimize loss.
- Output capacitor: 470µF, 50V, low ESR (Panasonic FR series) – reduces ripple to <5% of LED current.
- Current-sense resistor: 0.1Ω, 2W, metal film (Vishay) – low temperature coefficient (±50ppm/°C).
- Dimming interface: TL431 shunt regulator plus a 10kΩ potentiometer to set the reference voltage from 0.1V to 1V. This gives 10%–100% current.
- Input bridge rectifier: GBU4J (4A, 600V) – adequate headroom.
- EMI filter: Common-mode choke 2×10mH and X-cap 0.1µF – meets CISPR 22 Class B.

Simulation Tips and What to Look For
Use LTspice with a flyback model. Key waveforms to verify:
- MOSFET drain voltage: Should clamp at V_in_max + V_reflected + leakage spike. Expect ~480V at 240VAC – ensure the 650V FET has 20% margin.
- Inductor current: Should be a triangle wave touching zero each cycle (CrCM). Check that frequency stays above 20kHz (audible noise) and below 100kHz (switching loss).
- Output current ripple: Simulate with a 36V LED model (a Zener diode + resistor) – look for ±5% ripple. Adjust output cap if needed.
- PFC test: Add a 50Ω source impedance and measure input current harmonics. The L6562A should keep THD <15%.
Simulate dimming by sweeping the reference voltage – ensure stable operation without oscillation at low currents (use a 1nF capacitor on the comp pin).

Prototype Build and Testing Methodology
Build on a 2-layer PCB with a dedicated ground plane. Start with a benchtop variable AC supply (isolation transformer) and a series incandescent bulb (100W) to limit fault current. First power-up: apply 120VAC via the bulb – if it glows bright, there is a short; if dim, the circuit is likely OK. Measure output voltage with no LED load – should be clamped to 38V by a Zener. Then connect the floodlight’s LED board (remove its internal driver). Use a thermal camera to check the MOSFET and diode temperatures – they should stay below 85°C. Test dimming from 0–10V (use a lab DC supply) and verify linearity. Also, test under 100VAC, 230VAC, and 264VAC (max) to confirm regulation.

Performance Verification and Optimization
Measure with a power analyzer: efficiency, PF, and THD. Expected results: at 230VAC, efficiency >91%, PF >0.95. Compare output current ripple using an oscilloscope across a 0.05Ω series sense resistor. Optimization tips: if efficiency is low, increase the air gap slightly to reduce L_p (but check for saturation). If dimming below 10% causes flicker, add a minimum load resistor (e.g., 1kΩ across the LED) or increase the comp capacitor. For thermal, mount the MOSFET on the floodlight’s backplate with a mica insulator – this leverages the existing heatsink. Finally, run a 24-hour soak test at full brightness in a 40°C chamber to verify the over-temperature protection triggers at 85°C case temperature. This completes the design – you now have a dimmable, high-PF, constant-current driver that is both educational and field-repairable.

WX-DTVY-2

LED FLOODLIGHT MINI 50W-5400LM,

Interlight | WX-DTVY-2 | $92.39

View Product →

Related Products

Part Number / DescriptionManufacturer PackageUnit PriceAvailability QTYAdd To Cart
LED FLOODLIGHT MINI 50W-5400LM, LED FLOODLIGHT MINI 50W-5400LM,LED Lamp Replacement Interlight— $92.39 Out of Stock0 pcs
Nginx server needs to configure pseudo-static rules, click View configuration method