SP8T Terminated Switch App Note: 18GHz SMA Design Guide
The R574433805 is a terminated single-pole, eight-throw (SP8T) switch designed for high-frequency applications up to 18 GHz. Unlike a simple un-terminated switch, this component integrates 50-ohm loads on each of the eight throw ports. This topology is fundamental to your design approach: the switch is intended to route a single RF input to one active output while presenting a matched, non-reflective load to the other seven ports. Do not attempt to use the throw ports as bidirectional paths; the internal terminations are fixed and will absorb energy if you try to inject a signal into a throw. Your recommended circuit topology is therefore a star configuration: the common RF input (the pole) connects to your source, and each throw connects directly to a dedicated receiver, test point, or antenna path. For best isolation, keep the unused throws terminated—they already are—but ensure that any external circuitry on an active throw does not create a parallel resonance with the internal load. If you need to extend the frequency range or improve return loss, consider placing a shunt 50-ohm resistor at the pole only if your source impedance is not purely resistive; otherwise, rely on the switch’s internal matching.
Component selection for supporting passives is critical, particularly for the DC bias and control lines. The switch uses a TTL or CMOS-compatible driver, but you must select a series resistor (typically 100-200 ohms) on each control line close to the switch’s logic pins to dampen any ringing caused by trace inductance. For the power supply decoupling, use a 100 pF capacitor in parallel with a 0.1 µF capacitor placed within 2 mm of the Vcc pin, and a 10 µF bulk capacitor further away on the same rail. Do not use ferrite beads on the RF path—this is a terminated switch, and the insertion loss is already specified; a bead will add unwanted inductance. For the RF connectors, use high-quality SMA launch connectors with a dielectric that matches your PCB material (e.g., Rogers 4003 or 4350). If you are using a cable assembly, ensure the cable’s center conductor is not over-stressed during mating; use torque wrenches to 8 in-lbs. For the logic lines, use 74LVC1G125 buffers if you need to isolate the switch driver from a noisy microcontroller, but avoid level shifters with slow rise times—the switch’s internal decoder requires fast edges to prevent intermediate states.
PCB layout is where this component succeeds or fails. The R574433805 has a ground plane on the bottom and RF launch pads on the top; you must create a coplanar waveguide (CPWG) with ground via stitching along each RF trace to maintain 50-ohm impedance. The switch’s RF pads are designed for a 0.5 mm pitch; route the traces with a width calculated for your stack-up (typically 0.3 mm on 0.254 mm Rogers with a 0.2 mm gap to ground). Keep all eight RF traces identical in length to minimize phase skew if you are using this for a beamforming or MIMO application—if the application is not phase-sensitive, still keep them within 5 mm of each other to reduce crosstalk. Place ground vias on either side of every RF trace at a spacing of λ/20 (about 0.8 mm at 18 GHz) to suppress parallel-plate modes. For the control lines, route them on the bottom layer or an inner layer to avoid coupling into the RF plane; if they must cross an RF trace, do so at 90 degrees and with a ground via adjacent to the crossing point. The thermal pad on the bottom of the switch is a ground connection—solder it thoroughly to the PCB ground plane; do not leave it floating, as it also provides a return current path for the internal terminations.
EMC/EMI considerations are dominated by the high-frequency harmonics and the switching transients. The internal terminations absorb the RF energy, but the switching action creates digital noise on the Vcc rail. Add a 1 nF capacitor from each control line to ground at the switch’s logic pins to filter any high-frequency content that could couple to the RF output. For the RF path, the primary mitigation is shielding: use a metal shield can over the entire switch and the first 5 mm of each RF trace if your system is in a dense environment. If you cannot use a shield, ensure that the ground via fence around the switch is continuous—no gaps for the RF field to leak. Also, the internal terminations dissipate power; if you are switching high-level signals (e.g., +20 dBm), the switch body will heat up. This heat can cause frequency drift; ensure a thermal via array under the switch’s ground pad connects to a larger copper pour on the bottom layer. Avoid routing any DC or logic traces near the RF outputs; a 10 dB coupling from a logic line to an RF trace at 18 GHz is common if they run parallel for more than 3 mm.
Common design pitfalls include neglecting the switch’s settling time. The R574433805 has a typical switching time of 50 ns, but the RF output may show a glitch during the transition. Do not sample the RF output until at least 100 ns after the control line change; if your system uses a fast ADC, add a blanking signal. Another pitfall is assuming the internal terminations are perfect—they are specified to 18 GHz, but their VSWR degrades above 15 GHz. If your application requires a better match above 15 GHz, you must add external 50-ohm attenuators (e.g., 3 dB pads) on the throw ports, which will also add insertion loss. A third pitfall is incorrect logic polarity: verify the truth table for your specific variant (R574433805) because some versions use active-low enables. Finally, do not exceed the absolute maximum RF input power (+27 dBm); the internal terminations can only dissipate 0.5 W continuous. If you need to switch higher power, use an external circulator or a different switch.
For prototyping, start with a bare board and solder the switch using a hot-air rework station with a low-temperature profile (260°C max for 10 seconds) to avoid damaging the internal terminations. Use a vector network analyzer (VNA) to measure return loss at the common port with all throws terminated; you should see better than 15 dB return loss across the full band. Then, measure the insertion loss for each throw—they should be within 0.1 dB of each other. For bench testing, use a signal generator at 10 GHz and a power meter to verify the isolation between an active throw and an adjacent inactive throw; expect better than 60 dB. Test the switching speed with a fast oscilloscope and a 10 MHz square wave on the control line; check for any RF feedthrough during the transition. Finally, perform a thermal test: run the switch at +20 dBm for 30 minutes and verify the case temperature does not exceed 70°C. If you see any inconsistency, reflow the switch once—do not attempt to rework it more than twice, as the internal bond wires can fatigue.

