Home / Industry News

LT1462CS8 vs Alternatives: JFET Op-Amp Comparison Guide

GQGF LIMITED · 2026-08-10

The LT1462CS8#PBF, manufactured by Analog Devices Inc., belongs to the category of dual-channel, JFET-input operational amplifiers (op-amps) housed in an 8-pin SOIC package. This component is a precision analog building block designed to amplify, buffer, filter, or condition low-level signals in systems where high input impedance and low input bias current are critical. JFET-input op-amps are the go-to choice when the source impedance is high (e.g., photodiodes, pH sensors, piezoelectric transducers) because the FET gate draws virtually no DC current, preventing loading errors and preserving signal integrity. In a typical signal chain, this op-amp sits between a sensor and an ADC, performing impedance transformation, gain staging, or active filtering.

When selecting an op-amp of this class, the key parameters to evaluate are input bias current, input offset voltage, voltage noise density, gain-bandwidth product, and supply current. For JFET types, input bias current is often in the picoamp range (the LT1462 specifies 4 pA max at 25°C), which is essential for high-impedance sources. Offset voltage (2 mV max for the LT1462) determines DC accuracy; if you are amplifying small DC signals, a lower offset means less calibration effort. Voltage noise (20 nV/√Hz at 1 kHz) matters for low-frequency, low-level measurements, though JFET amps generally have higher noise than bipolar-input parts. The gain-bandwidth product (1.4 MHz for the LT1462) sets the maximum usable frequency for a given closed-loop gain, while supply current (typically 200 µA per amplifier) is critical for battery-powered or low-power designs. Additionally, look at supply voltage range (here ±2.5V to ±18V) and output swing (rail-to-rail output on the LT1462) to ensure compatibility with your ADC reference.

Compared to alternatives, the LT1462 sits in a distinct niche. Against standard bipolar op-amps like the LM358 or NE5532, it offers orders of magnitude lower input bias current and far higher input impedance, but at the cost of higher noise and a lower bandwidth. Against newer CMOS-input op-amps (e.g., OPA2376, MCP6022), the LT1462 has a wider supply voltage range and better offset voltage stability over temperature, but CMOS parts often achieve lower power and comparable bias currents. The LT1462 is a precision part, so its price is higher—typically $3–$5 in single-unit quantities versus $0.50–$1.50 for commodity JFET parts like the TL072. Availability is moderate; it is not a high-volume part, but it is not obsolete either. Lead times from major distributors usually range from 4–8 weeks for stock replenishment, though spot buys are often available. The LT1462 is also available as a single-channel (LT1461) and quad (LT1463) version, which helps with board layout if you need more channels.

Industry trends are reshaping this category. The push toward lower power and lower voltage operation is driving many designs to CMOS-input op-amps that operate at 1.8V or 3.3V, whereas the LT1462 requires at least ±2.5V. Simultaneously, the demand for higher precision in industrial IoT sensors is keeping JFET parts relevant because they offer the best combination of ultra-low bias current and wide supply headroom for 4-20 mA loops or ±15V industrial rails. Another trend is the move to smaller packages—while the LT1462 is only available in SOIC-8, newer competitors offer SOT-23 or even WLCSP packages, which matters for space-constrained designs. However, the LT1462’s proven reliability and long lifecycle (it has been in production for over 20 years) make it a safe choice for medical or aerospace applications where qualification costs are high.

Choose the LT1462CS8#PBF specifically when you need dual-channel precision with very high input impedance and you are operating on a dual supply of ±5V to ±15V. It excels in applications like photodiode transimpedance amplifiers, precision integrators, high-impedance buffer stages, and sample-and-hold circuits. If your design is battery-powered and only has a 3.3V rail, you would be better served by a CMOS op-amp like the ADA4610 or OPA2388. Conversely, if you need lower cost and can tolerate higher bias current (e.g., for audio line-level signals), the TL072 or OPA1642 offer better price-performance. For very low noise (e.g., microphone preamps), a bipolar-input part like the OPA1612 is superior, but it will load high-Z sources.

From a procurement perspective, treat the LT1462 as a mature, but not end-of-life, component. Analog Devices has not announced a discontinuation, and the part is still listed as active with a 10-year minimum buy window typical for their precision lines. Second-source options are limited—there is no direct pin-compatible drop-in from other manufacturers; the closest functional equivalents are the Texas Instruments LF412 or the ON Semiconductor NCS214, but these have slightly different specs (e.g., higher offset voltage or lower bandwidth). Therefore, if you design in the LT1462, you should commit to a single-source strategy. Order in volume (e.g., 500+ units) to secure lead times, and consider holding safety stock if your production runs are irregular. For new designs, always check the latest datasheet revision and contact the distributor for current lead time quotes, as Analog Devices has been shifting some production to newer fabs, which can cause sporadic shortages. If you need a guaranteed long-term supply, you might also evaluate the through-hole version (LT1462CN8) for legacy boards, but for new surface-mount designs, the SOIC-8 is the standard choice. In summary, the LT1462CS8#PBF is a reliable, high-performance JFET op-amp for precision analog applications, but be prepared to manage its single-source status and plan your inventory accordingly.

LT1462CS8#PBF

IC OPAMP JFET 2 CIRCUIT 8SO

Analog Devices Inc. | LT1462CS8#PBF | $7.32

View Product →

Related Products

Part Number / DescriptionManufacturer PackageUnit PriceAvailability QTYAdd To Cart
IC OPAMP JFET 2 CIRCUIT 8SO IC OPAMP JFET 2 CIRCUIT 8SOJ-FET Amplifier 2 Circuit 8-SO Analog Devices Inc.— $7.32 Out of Stock0 pcs
Nginx server needs to configure pseudo-static rules, click View configuration method