SC PC Simplex Plug SM126UM F728002100 Datasheet Guide Explained
The Radiall USA, Inc. F728002100, designated under the SC PC SIMPLEX PLUG SM126UM FOR C family, is a single-mode simplex fiber optic connector plug designed for 126 µm cladding fiber. While it is not a semiconductor device with traditional voltage and current ratings, its datasheet must be interpreted with the same rigor as any active component, because its optical and mechanical parameters directly govern link budget, return loss, and long-term reliability in telecom and datacom infrastructure.
Key optical and electrical-equivalent specifications. The most critical parameter is insertion loss, typically specified as ≤0.3 dB for a mated pair under controlled conditions. In practice, this value represents the worst-case attenuation added to the optical path by the connector interface. A lower insertion loss directly increases the available power margin at the receiver, which is especially important in passive optical networks (PONs) where splitters already consume significant budget. Return loss, or back reflection, is another primary specification; for this SC/PC (Physical Contact) variant, return loss is typically ≥45 dB. A high return loss minimizes optical reflections that can destabilize distributed feedback (DFB) lasers or cause relative intensity noise (RIN) in analog CATV systems. The 126 µm cladding designation ensures compatibility with standard single-mode fiber per ITU-T G.652, but the 125 µm nominal cladding tolerance must be verified against the fiber’s actual cladding diameter to avoid ferrule bore mismatch.
Absolute maximum ratings and derating. The datasheet will list maximum tensile load, typically 100 N for a cabled assembly, and a minimum bend radius of 30 mm for the unstressed fiber and 60 mm under load. Exceeding the tensile rating risks fiber pull-out or ferrule cracking. Operating temperature range is usually −40 °C to +85 °C, but derating applies to mating durability: the connector is rated for 500 to 1000 mating cycles. Beyond that, insertion loss may increase by 0.1–0.2 dB due to ferrule endface wear. Storage temperature may extend to +100 °C, but prolonged exposure to high humidity can degrade the epoxy used to bond the fiber into the ferrule. For high-reliability applications, derate the maximum tensile load by 50% and limit mating cycles to 200 to preserve optical performance.
Typical application circuit analysis. In a typical single-mode link, the F728002100 plugs into an SC adapter or receptacle, mating with another SC/PC plug. The optical circuit is: transmitter (e.g., 1310 nm DFB laser) → fiber pigtail → SC plug → adapter → SC plug → fiber span → receiver. Each mated pair contributes insertion loss and return loss. A link budget calculation must sum connector losses, splice losses, and fiber attenuation. For a 20 km span at 1310 nm with 0.35 dB/km fiber, two connectors at 0.3 dB each, and two splices at 0.1 dB each, the total loss is 7.4 dB. If the transmitter launches 0 dBm and the receiver sensitivity is −28 dBm, the margin is 20.6 dB, which is adequate but leaves little room for aging or temperature effects. Using this connector with a lower-grade ferrule (e.g., ceramic vs. zirconia) could increase loss by 0.1 dB, so the datasheet’s material specification matters.
Pin configuration and package considerations. The SC connector is a push-pull, keyed interface with a 2.5 mm ferrule. The “simplex” designation means a single fiber per plug, as opposed to duplex SC (which has two fibers in one housing). The keying prevents rotational misalignment; the key must align with the adapter’s slot. The plug housing is typically made of UL 94 V-0 rated plastic, and the ferrule is zirconia ceramic for durability. The boot (strain relief) is color-coded: blue for PC, green for APC, and beige for multimode. This part is “SM126UM,” meaning single-mode 126 µm cladding, which is non-standard but used in some specialty fibers. Ensure the adapter and mating plug also support 126 µm cladding; a 125 µm ferrule may cause eccentricity and higher loss. The package is not hermetic, so moisture ingress can occur if the connector is not properly seated.
Thermal management guidelines. Fiber optic connectors do not dissipate power, but thermal expansion mismatch between the ceramic ferrule and plastic housing can cause ferrule protrusion or retraction. Over −40 °C to +85 °C, the ferrule may move by a few micrometers, changing physical contact force. If the connector is used near a high-power laser (e.g., >500 mW), the endface can heat due to absorbed light, especially if contaminated. The datasheet may specify a maximum optical power handling of 1 W for the connector interface. Thermal cycling tests (e.g., 100 cycles from −40 °C to +75 °C) are often listed; a change in insertion loss of ≤0.2 dB after cycling is acceptable. For outdoor applications, use a sealed adapter and a boot that resists UV degradation.
Reading timing diagrams and characteristic curves. This connector’s datasheet typically includes insertion loss vs. mating cycles, return loss vs. wavelength (e.g., 1310 nm and 1550 nm), and tensile load vs. displacement. The mating cycle curve shows a gradual increase in loss after 500 cycles, with a sharp rise after 1000 cycles—indicating the endface is wearing. The return loss vs. wavelength curve should be flat across the operating band; a dip near 1380 nm (water peak) is normal for single-mode fiber but not for the connector itself. The tensile load curve has a linear region up to 100 N, then a yield point where the fiber begins to slip. Interpret these curves with the understanding that they are measured under clean, dry conditions; contamination can shift insertion loss by 1 dB or more. Always clean and inspect the endface before mating, and use an interferometer to verify endface geometry if the link margin is tight.

