Application Note: Using the FOR BOXLIGHT SE-12SF Bulb (WW-0HDF-7)
The Interlight WW-0HDF-7 is a direct replacement bulb assembly for the BOXLIGHT SE-12SF projector, and treating it as a simple resistive load will lead to premature failures. This component is a high-intensity discharge lamp module that requires a properly matched electronic ballast to strike and regulate the arc. The most reliable topology for driving this bulb is a two-stage converter: a power-factor-corrected (PFC) boost front end followed by a full-bridge or half-bridge resonant inverter with current-mode control. The PFC stage should target a regulated 380 VDC bus with a switching frequency between 60 kHz and 100 kHz, while the inverter should operate in a resonant mode near 100 kHz to achieve zero-voltage switching (ZVS). Avoid simple flyback or forward converters, as they cannot deliver the high ignition voltage—typically 3 kV to 5 kV—required to break down the lamp gas. Instead, incorporate a dedicated high-voltage ignition circuit, such as a pulse transformer driven by a capacitor discharge, that is disabled once the arc is established. Design best practices include soft-start ramping of lamp current over 2 to 5 seconds, closed-loop current regulation to within ±5 percent, and a fault-protection state machine that shuts down the inverter if the lamp fails to strike within 100 ms.
Supporting passive selection is critical for reliability. The PFC inductor should use a gapped ferrite core (e.g., PC95 material) with a saturation current at least 1.5 times the peak switch current, and the boost diode must be a silicon carbide (SiC) Schottky type rated for 600 V and 10 A to minimize reverse recovery losses. For the inverter, select film capacitors (polypropylene) for the resonant tank with a voltage rating of 630 VDC and a low dissipation factor. The current-sense resistor in the lamp return path should be a non-inductive metal-element type with a temperature coefficient below 50 ppm/°C and a power rating of at least 2 W. Bulk electrolytic capacitors on the 380 V bus should be rated for 450 V and 105°C, with a ripple current rating exceeding the expected RMS by 30 percent. Gate drive resistors should be between 5 Ω and 15 Ω to control switching slew rates without excessive ringing. Do not use generic ceramic capacitors in the resonant tank—their voltage coefficient and piezoelectric effects will cause frequency drift and audible noise.
PCB layout must respect the high voltages and fast edges present in this design. Place the PFC and inverter power stages on opposite sides of the board or at least 15 mm apart, with a clear ground plane partition between them. Route the high-voltage ignition trace as a short, wide (minimum 2 mm) track on the top layer, away from any sensitive analog feedback lines. Use a star ground for the current-sense return, connecting it directly to the bulk capacitor negative terminal. Keep the gate loop area under 1 cm² by placing the gate driver within 5 mm of the MOSFET and using a return path directly beneath the gate trace. For the resonant tank, minimize loop inductance by placing the resonant capacitor and inductor adjacent to each other and using thick copper (2 oz or more). Thermal relief is essential: the lamp connector and the inverter MOSFETs should have thermal vias to a bottom-side copper pour, and the PFC inductor should not be placed near the lamp’s heat plume. Route the lamp current sense traces as a differential pair with matched lengths and a ground guard trace.
EMC/EMI mitigation starts with the PFC stage, which is the dominant source of conducted emissions below 30 MHz. Add a two-stage common-mode choke after the AC rectifier, with a leakage inductance sufficient to attenuate 150 kHz to 1 MHz noise by at least 40 dB. Use Y-capacitors (2.2 nF, 250 VAC) from each line to chassis ground, but ensure the total leakage current stays below 250 µA for safety. For radiated emissions from the inverter, place a copper shield over the resonant tank and connect it to the primary ground at multiple points. Slow the MOSFET turn-on with a gate resistor of 10 Ω to 22 Ω, but verify that ZVS is maintained. Add a snubber (RC, 100 Ω and 1 nF) across the inverter’s high-side switch if ringing exceeds 50 V above the bus. The ignition transformer should be potted or shielded to contain its high-frequency pulse. Finally, use a spread-spectrum modulation on the PFC switching frequency (±5 percent) to reduce peak emissions at the fundamental.
Common design pitfalls include underestimating the ignition voltage, which can cause the lamp to fail to strike and the ballast to enter a repetitive hiccup mode. Always measure the open-circuit ignition pulse with a high-voltage probe and ensure it exceeds 4 kV for a cold lamp. Another pitfall is inadequate current regulation during lamp warm-up; the lamp’s voltage drops from over 200 V to below 100 V in the first 30 seconds, and a fixed-duty-cycle inverter will overdrive the lamp and destroy it. Implement a closed-loop current controller with a slow integrator (time constant 100 ms) to track this transition. A third pitfall is thermal cycling of the lamp connector: use a high-temperature (200°C) silicone-insulated wire and a ceramic connector body, not plastic. Finally, do not omit the bleeder resistor across the bulk capacitor—it must discharge the 380 V bus to below 60 V within 2 seconds for safety.
For prototyping, build the PFC and inverter on separate boards connected by a short, twisted pair for the 380 V bus. Use a current-limited DC supply set to 400 V and 1 A for initial inverter testing without the lamp, substituting a 100 Ω, 500 W resistor as a dummy load. Verify ZVS by observing the drain-source voltage with a differential probe—there should be no voltage spike above 450 V. Once the inverter is stable, connect the lamp through a 10 Ω, 50 W series resistor to limit strike current, then remove it after the arc stabilizes. Bench-test the ignition circuit separately with a spark gap or a 1 MΩ high-voltage probe. Measure conducted emissions with a LISN and a spectrum analyzer from 150 kHz to 30 MHz. Run a 24-hour burn-in at 25°C and 50°C ambient, logging lamp current, bus voltage, and MOSFET case temperature. Any drift over 5 percent in lamp current indicates a thermal compensation problem in the feedback network.

