FOR DUKANE 456-161 2 PACK (WW-19BJ-9) Application Note
The Interlight WW-19BJ-9 is a two-pack replacement lamp assembly intended for Dukane 456-161 projector and lighting systems. Because this is an electro-optical and thermal assembly rather than a logic component, integration success depends less on exotic circuitry and more on respecting the lamp's electrical drive envelope, thermal limits, and mechanical mounting. The most reliable topology is a current-regulated DC drive with a soft-start ramp. Whether the host uses a buck, boost, or buck-boost converter, the converter's control loop must be sized for the lamp's cold-filament inrush, which can be several times the steady-state current. A dedicated constant-current controller with an adjustable current-sense threshold and a programmed startup slew rate is strongly preferred over a fixed-voltage supply. If the original Dukane ballast or driver is retained, verify that its compliance voltage and current limits fall within the replacement lamp's ratings before energizing, and add a series current-limit element only if the driver lacks regulation. Include a reverse-polarity protection device and a transient suppressor across the lamp terminals, and provide a defined off-state path so stored energy in the harness cannot flash the lamp during shutdown.
Supporting passives deserve more attention than they typically receive. The current-sense resistor should be a low-inductance, low-TCR type rated for at least twice the expected RMS current, with a Kelvin-sense connection to the controller. The inductor or transformer in the drive stage must be specified for the lamp's peak current with saturation margin, and its core loss must be evaluated at the actual switching frequency. Input and output capacitors should be selected with ripple-current ratings that account for lamp inrush, and electrolytics should be derated for the elevated local temperature near the lamp housing. Use high-temperature-rated capacitors and wiring insulation rated for the assembly's thermal environment, and keep the wiring gauge sized so that voltage drop at the lamp does not exceed the driver's regulation headroom. For any control or sense signals routed near the lamp, specify shielded or twisted-pair cable to reduce noise pickup.
PCB and mechanical layout should separate the power stage from any control logic. Place the switching converter close to its input bulk capacitance and the lamp connector, keeping the high-current loop as small as possible. Route lamp leads away from sensitive analog or digital traces, and avoid running power and return paths in parallel over long distances. Provide adequate copper area and thermal vias under dissipating components, and position the lamp assembly so that convection paths are not blocked by the PCB or enclosure walls. Because this is a two-lamp pack, mirror the layout for the second channel and keep the two high-current loops symmetrical to avoid differential heating or crosstalk. Use locking connectors and strain relief on the lamp harness; vibration and thermal cycling are common causes of intermittent contact in projector installations.
EMC performance is dominated by the switching converter and the lamp harness, which can act as an antenna. Keep the switching node area small, use a snubber or ferrite bead where ringing is severe, and add common-mode chokes or ferrite sleeves on the lamp leads if radiated emissions are a concern. Ground the lamp return at the connector shell or a dedicated return plane, and avoid relying on the chassis as a current-carrying path. Where the enclosure is metallic, ensure bonding at multiple points; where it is plastic, consider a conductive coating or internal shielding only if testing shows it is needed. Test conducted emissions at the input terminals and radiated emissions with the lamp installed and operating, since the lamp itself changes the load impedance and harmonic profile.
Common pitfalls include ignoring cold-filament inrush, which can trip the driver's overcurrent protection or overstress the passives; under-sizing the thermal design so that the lamp's local ambient exceeds ratings after warm-up; and mixing the two lamps' harnesses or polarity. Another frequent error is assuming the replacement lamp is electrically identical to the original without verifying voltage and current ratings. Avoid these by characterizing the lamp at cold and hot states, documenting the driver's limits, and performing a thermal soak test in the actual enclosure. Also verify connector mating force and retention after thermal cycling.
For prototyping, build the drive stage on a bench board with adjustable current limit and measure lamp voltage and current with a differential probe or an isolated current probe. Use a current-limited supply for first power-up, ramp the current slowly, and log the inrush waveform. Perform a thermal soak at maximum rated drive until temperatures stabilize, then repeat at minimum and maximum supply voltages. Verify startup, shutdown, and fault behavior, then run an extended burn-in with the lamp in its final orientation. Bench testing should include a brownout and restart sequence and a simulated connector-disconnect event to confirm no destructive transients reach the driver.

