Home / Focus on hot spots

Schneider SH30702P1AF3000 Design Tutorial: Step-by-Step Guide

GQGF LIMITED · 2026-10-28

This tutorial uses the Schneider Electric SH30702P1AF3000, a Harmony XB5-series 30 mm pushbutton with a 1 NO + 1 NC contact block, as the human-machine interface element in a small industrial control circuit. What makes it suitable for a teaching build is its robustness and clarity: it is a panel-mount, IP66-rated momentary actuator with a spring-return mechanism, screw-clamp terminals rated for 10 A at 600 V AC, and a mechanically coupled contact pair. That combination gives you a component that behaves like a real plant pushbutton, is easy to wire with standard ferrules, and lets you demonstrate both a start function and a fail-safe stop function from a single device.

Design requirements. The circuit is a 24 V DC motor-start control loop with a latching relay and a safety stop path. Requirements: (1) a momentary start input from the NO contact; (2) an NC contact that opens on actuation and is wired in series with the coil supply as a stop element; (3) a relay coil drawing no more than 100 mA; (4) a 24 V DC supply with at least 1 A headroom; (5) a status LED across the coil; (6) all wiring rated for the 24 V loop and terminated in a DIN-rail enclosure. The pushbutton's 10 A contact rating is far above the loop current, so contact life is effectively unlimited for this duty.

Step-by-step design. Start with the coil. Choose a 24 V DC relay with a 24 V coil, 8 A contact rating, and a coil resistance of about 400 ohms. Coil current is I = V/R = 24/400 = 60 mA. Add a flyback diode across the coil (1N4007 is adequate) to clamp the inductive kick; without it, the switch contacts will arc and the diode protects the electronics. Next, size the LED indicator: with a 2 V forward drop and 10 mA target, R = (24 − 2)/0.010 = 2.2 kΩ (use a 1/4 W part). Then verify the supply: 60 mA coil plus 10 mA LED plus margin gives roughly 100 mA, so a 24 V, 1 A DIN-rail supply is comfortable. Finally, map the contacts: terminal pair 1–2 is the NO start contact, and pair 3–4 is the NC stop contact. Wire the NC contact in series with the coil so that pressing the button removes coil power — the classic stop configuration.

BOM rationale. The SH30702P1AF3000 supplies both contacts in one 30 mm body, avoiding a second panel cutout and simplifying the enclosure layout. Its screw terminals accept 0.5–2.5 mm² conductors, so 1.0 mm² panel wire is appropriate. Pair it with a 24 V DC relay, a 1N4007 flyback diode, a 2.2 kΩ resistor and 5 mm red LED, a 24 V 1 A DIN-rail supply, a DIN-rail enclosure, and 1.0 mm² ferruled wire. A normally-closed auxiliary contact on the relay provides the latch path, completing the classic start/stop circuit.

Simulation tips. Before building, model the loop in a free SPICE tool. Represent the coil as a 400 Ω resistor in series with a 100 mH inductor, add the flyback diode, and drive the node with a pulsed voltage source to mimic the pushbutton. Look for two things: the coil current should settle near 60 mA and the diode clamp voltage should stay below about 0.8 V during turn-off. Also check the LED branch current stays near 10 mA. If the simulated coil current is much higher than calculated, your relay model is wrong — verify with a multimeter on the real coil.

Prototype build and testing. Mount the pushbutton in a panel cutout, wire the NC contact in series with the coil supply, and the NO contact in parallel with the relay's latching contact. Power up with the button released: the relay should be de-energized. Press and hold: the relay should pull in and latch. Release: the relay should stay latched. Press again: the NC contact should break the coil circuit and drop the relay. Test with a multimeter across the coil and confirm the LED lights only when the relay is energized. Do a continuity check on both contact pairs with the button released and pressed to confirm NO/NC behavior.

Performance verification and optimization. Measure coil voltage at pull-in and hold, and confirm the supply stays above 22 V under load. Check that the button resets cleanly every time — a sticky return spring is the most common field failure. For optimization, add an RC snubber across the relay contacts if you drive an inductive load, and consider a second NC contact for an emergency-stop path in series with the supply. Finally, document the terminal numbering on the enclosure label: the SH30702P1AF3000's contact blocks are keyed, so miswiring is rare, but labeling the start and stop paths prevents confusion during maintenance.

SH30702P1AF3000

Schneider Electric

Schneider Electric | SH30702P1AF3000 | $2,761.54

View Product →

Related Products

Part Number / DescriptionManufacturer PackageUnit PriceAvailability QTYAdd To Cart
Schneider Electric Schneider ElectricSH3 OMC 70.2 key enc. ST ang.conn. Brk Schneider Electric— $2,761.54 Out of Stock0 pcs
Nginx server needs to configure pseudo-static rules, click View configuration method