Home / Industry News

Troubleshooting RES SMD 100 OHM 1W 2010 WIDE (LTR50UZPF1000) Failures

GQGF LIMITED · 2026-11-14

When customers call me about the Rohm LTR50UZPF1000 (100 Ω, 1 W, 2010 wide-terminal), the conversation usually starts with "the resistor is bad." In my experience, maybe one in ten of those calls ends with the resistor actually being at fault. The wide-terminal 2010 package is a low-inductance, high-power-density part often used as a current-sense element, a snubber, or a gate resistor, so the surrounding circuit is usually where the real problem lives. Here is how I walk through it.

Typical failure modes and root causes. The most common failure I see is a cracked or delaminated terminal from thermal cycling or mechanical flexing, which shows up as an open or a large resistance shift. Next is a burned or discolored body from sustained overload — this part is rated 1 W, but that rating assumes adequate copper and a 70 °C+ derating curve, and I have seen it run at 1.2 W in still air with no thermal relief and drift upward over months. Solder voids under the wide terminals are a frequent root cause of hot spots. Less common but real: ESD or surge damage when the resistor sits on a sense line exposed to transients, and corrosion from no-clean flux residue in humid environments.

Step-by-step debugging methodology. First, measure the resistor in-circuit with the power off and the node isolated — if you read anything far from 100 Ω (say below 90 Ω or above 110 Ω), lift one end and remeasure. Second, check the voltage across it under load and compute dissipation; if it exceeds 0.7 W in a 2010 footprint, treat thermal design as suspect. Third, inspect the solder joints with a low-power microscope and look for voids, fillets, and cracking at the wide terminations. Fourth, thermally image the board under load — a hot resistor with a cold neighbor usually means the copper is not spreading heat. Fifth, if the resistor reads fine, move to the surrounding circuit: the driver, the sense amplifier, or the load.

Common schematic and layout mistakes. The biggest one is treating a wide-terminal 2010 as a drop-in for a standard 2010 — the pad geometry is different, and a mismatched footprint creates voids and stress risers. Second is no thermal relief: the wide terminals need generous copper on both ends, and I have seen customers put them on 10-mil traces. Third is placing the resistor next to a hot switching device without derating. Fourth is routing a sense trace under the resistor body, coupling switching noise into the measurement. Fifth is omitting a series resistor or TVS on a sense line that sees transients. Always check the pad drawing against the datasheet land pattern before you sign off.

Verifying authenticity and quality. Rohm parts carry a laser-marked value and lot code; I compare the marking against the datasheet and check the packaging for the Rohm label and reel format. Measure a sample of ten from the reel with a 4-wire meter — a tight distribution around 100 Ω is a good sign, and outliers or a bimodal spread suggest a counterfeit or a mixed lot. Check the body dimensions and terminal width against the drawing; counterfeit 2010s often have standard-width terminals. Finally, do a quick load test at rated power for 30 minutes and watch for drift — genuine parts hold within a fraction of a percent.

Measurement techniques and equipment. Use a 4-wire Kelvin meter or a bench DMM with a 4-wire mode for anything below a few ohms; for a 100 Ω part a good 4.5-digit DMM is fine, but for in-circuit sense work use a differential probe and an oscilloscope with adequate bandwidth. A thermal camera (or at minimum a thermocouple on the body) is essential for power resistors. For transient work, a current probe on the sense line tells you more than any voltage measurement. Avoid cheap two-wire meters for in-circuit checks — lead resistance and probe contact dominate the error.

When to suspect the component versus the circuit. Suspect the resistor only if it is out of tolerance when isolated, visibly cracked or discolored, or drifting under load. If it reads 100 Ω cold and the circuit still misbehaves, the problem is almost certainly elsewhere — a bad driver, a ground loop, or a sense amplifier with insufficient common-mode range. Isolate the resistor first, then stop blaming it.

Real-world case studies. One customer reported repeated opens on a motor-drive sense resistor; the resistor was fine, but the layout ran the sense trace parallel to the gate drive, and the induced spike exceeded the part's pulse rating. Adding a series resistor and rerouting fixed it. Another customer saw the resistor drift to 130 Ω over six months; the root cause was a 0.9 W continuous load in a sealed enclosure with no thermal relief — a copper pour and a derating review solved it. A third had a "dead" resistor that turned out to be a cold solder joint on one wide terminal, invisible until we X-rayed it. In each case, the resistor was the messenger, not the culprit.

LTR50UZPF1000

RES SMD 100 OHM 1W 2010 WIDE

Rohm Semiconductor | LTR50UZPF1000 | $0.69

View Product →

Related Products

Part Number / DescriptionManufacturer PackageUnit PriceAvailability QTYAdd To Cart
RES SMD 100 OHM 1W 2010 WIDE RES SMD 100 OHM 1W 2010 WIDE100 Ohms ±1% 1W Chip Resistor Wide 2010 (5025 Metric), 1020 Automotive AEC-Q200, Pulse Withstanding Thick Film Rohm Semiconductor— $0.69 Out of Stock0 pcs
Nginx server needs to configure pseudo-static rules, click View configuration method